LockedResetting the "wrench" service light.

Post
n00b2u
Puddle Jumper
2009/03/30 22:34:37
Is there an easy way to reset the wrench light without taking it to the dealer? The local dealer said that light means its time to get it serviced, but I know its got fresh oil/filter/gear oil. (have not purchased the bike yet and wanted to check on this. Wrench light is flashing) 07 800 efi
Bobber
Puddle Jumper
Re:Resetting the "wrench" service light. 2009/03/30 23:23:57
You can reset it yourself in the diagnostic mode which is done by putting the tranny in neutral,hold the yellow override button for 5 seconds then turn the key on and release the button.Then scroll through the functions with the override button.
n00b2u
Puddle Jumper
Re:Resetting the "wrench" service light. 2009/03/31 00:38:08
thanks for the info!
heyfollowme
Mud Maniac
Re:Resetting the "wrench" service light. 2009/03/31 02:07:11
thanks for the info bobber i have an 06 sportsman 450 as well and i need to turn that same light off thanks
Dirtbmw20
Outlaw
Re:Resetting the "wrench" service light. 2009/03/31 08:16:40
All this info is in the owners manual.

Instrument Cluster
Rider Information Center
Diagnostic Mode
The diagnostic mode is for informational purposes only. Please return
your ATV to your dealer for all major repairs.
As long as the gauge is in the diagnostic mode, the wrench icon will
remain lit.
To leave the diagnostic mode, turn the key switch off and on.
NOTE: Any movement of the tires will also take the machine out of
the diagnostic mode.
To enter the diagnostics mode:
1. Turn the key switch off and wait 10 seconds.
2. Set the park brake and shift the transmission to neutral.
3. Hold the mode/reverse override button and turn the key switch on.
4. Release the switch as soon as the display is activated.
The initial screen display refers to the software version installed in
your ATV. This information is displayed briefly.
Use the mode/reverse override button to toggle through the diagnostic
screens.
Screen 1: Battery voltage
Screen 2: Tachometer
Screen 3: AWD diagnostic
This gauge indicates whether or not current is flowing through the
AWD coil (only on models with switchable AWD).
Screen 4: Gear circuit diagnostic
This screen displays the resistance value (in ohms) being read at the
gear switch input of the gauge.
FEATURES
Instrument Cluster
Rider Information Center
Diagnostic Mode
Screen 5: Programmable service interval
The purpose of the programmable service interval is to provide the
consumer and dealer with a convenient reminder for routine
maintenance. When your vehicle leaves the factory, this feature is set at
50 hours. You must enable the programmable service interval before it
can be used.
Once the service interval mode is set with the hours when service is
due, the hours of actual engine operation are subtracted from the set
hours until 0 is reached. When the counter reaches 0, the wrench icon
will flash quickly for 5 seconds each time the vehicle is started as a
reminder that the periodic maintenance is due.
To set the hours, press and hold the mode/override button until the
wrench icon flashes. When it begins to flash, release the button. The
setting will increase by one hour each time the button is pressed.
Pressing and holding the button will allow the numbers to escalate
much faster. When the desired time increment is displayed, release the
button and wait for the wrench to stop flashing. When the wrench
stops blinking, your service hours are set.
NOTE: If you scroll past the intended number, hold the button down
until the count turns over to 0. You can then reset the
number.
If the service interval is enabled on your ATV and you wish to turn it
off, toggle to the service interval mode. Press and hold the mode
button for approximately 7 seconds until the word OFF appears in the
Rider Information Center.
Screen 6: Miles/Kilometers toggle
The display in the tripmeter and odometer can be changed to display
either kilometers or miles. The current display mode will be shown as
KM or MP. To change, hold in the mode button until the letters flash,
then press and release the button once. When the display stops
flashing, the mode has been set.
Thor
Mud Slinger
Re:Resetting the "wrench" service light. 2009/03/31 10:08:31
dirtbmw20 is do you know of a online owners manual for the 800? I never got one with mine.
Dirtbmw20
Outlaw
Re:Resetting the "wrench" service light. 2009/03/31 11:21:44
Thor

dirtbmw20 is do you know of a online owners manual for the 800? I never got one with mine.

Owners AND parts manuals are free on this site............................
http://www.polarisindustries.com/vehicles/templates/Manuals.aspx?NRMODE=Published&NRORIGINALURL=%2fen-US%2fRidersPortal%2fManualsAndParts%2f&NRNODEGUID=%7bFB37A1BA-27E9-40A7-899D-4DA93DCA59FF%7d&NRCACHEHINT=Guest

 
Thor
Mud Slinger
Re:Resetting the "wrench" service light. 2009/03/31 11:26:40
Thank you. That is great how Polaris does that.